MENU

Qubino Flush Dimmer ZMNHDD2 Aus/NZ Frequency 921.42 MHz

Qubino Flush Dimmer ZMNHDD2  Aus/NZ Frequency 921.42 MHz
The Qubino Flush Dimmer is the first MOSFET-switching lights device that also supports control of low-voltage halogen lamps with electronic transformer, dimmable compact fluorescent lights and dimmable LED bulbs. It also measures the power consumption of electrical devices and supports the connection of a digital temperature sensor.

The Qubino Flush Dimmer can measure the power consumption of the connected electrical device and itself has an extremely low power consumption of just 0.7 W.

The Qubino Flush Dimmer can operate across a wide temperature range, from a chilly -10˚C to a scorching 40˚C (14˚–104˚F). It supports the connection of a digital temperature sensor, which is also useful for creating complex scenes. Every device also acts as a repeater in order to improve the range and stability of the Z-Wave network.

Extremely small size and a specially designed casing mean that connecting the device inside a flush mounting box is simplicity itself. The installation process, tested and approved by professional electricians, consists of just three simple steps:

1, Remove the switches from the box and disconnect the wires.
2, Connect the wires to the Qubino device and insert it in the box.
3, Fix the switches to the box.

Warning:
Danger of electrocution !
All works on the device may be performed only by a qualified and licensed electrician. Observe national regulations.
Even when the device is turned off, voltage may be present at its terminals. Any works introducing changes into the configuration of connections or the load must be always performed with disconnected voltage (disable the fuse).

For more informations, please follow the links below.
RRP:
NZ$ 129.00
Limited Stock:
Only 2 remaining at this price
Price:
NZ$ 116.10
Shipping:
NZ$ 6.00
Purchase Qty:
 
Technical specifications

Electrical diagram 230VAC qubino-flush-dimmer-24vdc-1-224x300

Power supply 110 - 230 VAC ±10%
50 / 60 Hz, (24–30 VDC)
Rated load current of AC output (resistive load)* 0.6 A / 230 VAC
Rated load current of DC output (resistive load) 0.85 A / 30 VDC
Output circuit power of AC output (resistive load) 140 W (230 VAC)
Output circuit power of DC output (resistive load) 21 W (24 VDC)
Power measurement accuracy +/- 2 W
Digital temperature sensor range
(sensor must be ordered separately)
-50° ~ +125°C
Operation temperature -10° ~ +40°C
Distance up to 30 m indoors
(depending on building materials)
Dimensions (WxHxD) 41.8 x 36.8 x 15.4 mm
(packaging) (79 x 52 x 22 mm)
Weight (including packaging) 28 g (34 g)
Electricity consumption 0.7 W
For installation in boxes Ø ≥ 60 mm or 2 M, depth ≥ 60 mm
Switching MOSFET (trailing edge)

Setting Parameters

Parameter no. 1 & no. 2 – Input I1 & Input I2 switch type

Available configuration parameters (data type is 1 Byte DEC):

  • default value 0
  • 0 mono-stable switch type (push button) - button quick press turns between previous set Dimmer value and zero
  • 1 bi-stable switch type

Parameter no. 3 & no. 4 – Input I2 & Input I3 contact type

Available configuration parameters (data type is 1 Byte DEC):

  • default value 0
  • 0 NO (normally open) input type
  • 1 NC (normally close) input type

Parameter no. 11 - Automatic turning off output after set time

Available configuration parameters (data type is 2 Byte DEC):

  • Default value 0
  • 0 - Auto OFF disabled
  • 1 – 32536 = 1 second – 32536 seconds Auto OFF enabled with define time, step is 1 second.

Parameter no. 12 - Automatic turning on output after set time

Available configuration parameters (data type is 2 Byte DEC):

  • Default value 0
  • 0 - Auto ON disabled
  • 1 – 32535 = 1 second – 32535 seconds Auto ON enabled with define time, step is 1 second.

Parameter no. 20 – Enable Disable 3-way switch

Available configuration parameters (data type is 1 Byte DEC):

Dimming is done by push button or switch connected to I1 (by default). Enabling 3 way switch dimming can be controlled by push button or switch connected to I1 and I2.

  • default value 0
  • 0 – single push button (connected to I1)
  • 1 – 3 way switch (connected to I1 and I2)

Parameter no. 21 – Enable/Disable Double click function

If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value. Available configuration parameters (data type is 1 Byte DEC):

  • Default value 0
  • 0 – double click disabled
  • 1 – double click enabled

Parameter no. 30 - Saving the state of the device after a power failure

Available configuration parameters (data type is 1 Byte DEC):

  • default value 0
  • 0 – Flush Dimmer device saves its state before power failure (it returns to the last position saved before a power failure)
  • 1 – Flush Dimmer device does not save the state after a power failure, it returns to "off" position.

Parameter no. 40 – Power reporting in Watts on power change

Set value means percentage, set value from 0 - 100 = 0 % - 100 %. Available configuration parameters (data type is 1 Byte DEC):

  • default value 5
  • 0 – Reporting Disabled
  • 1 – 100 = 1 % - 100 % Reporting enabled. Power report is sent (pushed) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1 %.

Note: If power change is less than 1 W, the report is not sent (pushed), independent of percentage set.

Parameter no. 42 – Power reporting in Watts by time interval

Set value means time interval (0 – 32767) in seconds, when power report is sent. Available configure. parameters (data type is 2 Byte DEC):

  • default value 0
  • 0 – Reporting Disabled
  • 1 – 32767 = 1 second – 32767 seconds. Reporting enabled. Power report is sent with time interval set by entered value.

Parameter no. 60 – Minimum dimming value

Available configuration parameters (data type is 1 Byte DEC):

  • Default value 1 = 1 % (Minimum dimming value)
  • 1- 98 = 1 % – 98 %, step is 1 %. Minimum dimming value is set by entered value.

Note: The minimum level may not be higher than the maximum level! 1 % min. dimming value is defined by Z-Wave multilevel device class.

Parameter no. 61 – Maximum dimming value

Available configuration parameters (data type is 1 Byte DEC):

  • Default value 99 = 99 % (Maximum dimming value)
  • 2- 99 = 2 % – 99 %, step is 1 %. Maximum dimming values is set by entered value.

Note: The maximum level may not be lower than the minimum level! 99 % max. dimming value is defined by Z-Wave multilevel device class.

Parameter no. 65 – Dimming time (soft on/off)

Set value means time of moving the Dimmer between min. and max. dimming values by short press of push button or controlled through UI (BasicSet). Available configuration parameters (data type is 2 Byte DEC):

  • Default value 100 = 1 s
  • 50 - 255 = 500 mseconds – 2550 mseconds (2,55 s), step is 10 mseconds

Parameter no. 66 – Dimming time when key pressed

Time of moving the Dimmer between min. and max dimming values by continues hold of push button or associated device. Available configuration parameters (data type is 2 Byte DEC):

  • Default value 3 = 3 s
  • 1 - 255 = 1 second – 255 seconds

https://www.youtube.com/watch?v=m3b_cuzKV7c&feature=youtu.be