Fibaro Roller Shutter 2 Module

Fibaro Roller Shutter 2 Module
FIBARO Roller Shutter 2 is a module designed to control AC motorised roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices. FIBARO Roller Shutter 2 allows precise positioning of roller blinds or venetian blind lamellas. The device is equipped with power and energy monitoring. The module is designed to be mounted inside a “flush mounting box”, hidden behind a traditional wall switch.

As with all other Actors, FIBARO Roller Shutter 2 allows to control connected devices either via the Z-Wave network or via a switch connected directly to it.

Ease of use and installation by qualified electrician only .

It's Aus/NZ model, the frequency: 921.42 MHz.

You can purchase this Fibaro Roller shutter 2 to work with our DC114M to control those Built-in 433.2 MHz RF receiver tubular motors or curtain motors.

It also can work with 82TV 5 wires curtain motors without major problem, there are a lot of people in the world said Fibaro roller shutter 2 module can not control 82TV curtain motor, the movement of opening or closing only last about 1 second and travels very short distance, we found the solution, the reason causes this problem is because the 82TV default switch setting is for Bi-stable (Toggle ) Switches, and Fibaro send the pulse signal to Q1 or Q2 , the pulse signal only last very short period, so the curtain motor can only move very short distance, so the first thing you need to do is set the curtain motor like usually: set up the RF handheld remote, set the open and close limit position by the 82TV motor itself, and then you should follow the 82TV motor's instruction to use the remote to change the motor's switch mode from the factory default setting Bi-stable switch model to Monostable ( Momentary ) switch mode , the other thing is because the 82TV motor has electronic memory limit position function itself, you can not do auto Calibration through Z-Wave module or the main controller, you can click and control the curtain open, close and stop, but you could not know the exactly position of the curtain moving and you can not set the curtain opening or closing percentage through the main controller UI as well, the Icon on the UI only can show fully open or fully close.

Danger of electrocution !
All works on the device may be performed only by a qualified and licensed electrician. Observe national regulations.
Even when the device is turned off, voltage may be present at its terminals. Any works introducing changes into the configuration of connections or the load must be always performed with disconnected voltage (disable the fuse).
NZ$ 139.00
NZ$ 125.10
NZ$ 6.00
Out Of Stock
  • Compatible with any Z-Wave Controller
  • Advanced microprocessor control
  • Executive element – electromagnetic, micro-gap relay switch
  • Works with various types of switches – momentary, toggle and dedicated roller blind switches
  • Active power and energy metering functionality
  • To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations

This device may be used with all devices certified with Z-Wave certificate and should be compatible with such devices produced by other manufacturers.

Power supply: 110-240 V AC, 50/60 Hz
Rated load current: 4.2A for lamps and resistive loads
1.7A for motors with compensated power factor (inductive loads)
Type of supported motor: single-phase AC motors
Supported limit switches type: electronic and mechanic
Power consumption: up to 0.8W
In accordance with EU standards: RED 2014/53/EU
RoHS 2011/65/EU
Operational temperature: 0-35°C
Active element: micro-gap relay switch μ
For installation in boxes:  Ø ≥ 50mm, depth ≥ 60mm
Radio protocol: Z-Wave
Radio signal power: up to 1mW
Radio frequency: 868.4 MHz EU;
908.4 MHz US;
921.4 MHz ANZ;
869.0 MHz RU;
865.2 MHz IN;
Range: up to 50 m outdoors
up to 30 m indoors
(depending on building materials)
Dimensions: (L x W x H)): 42.50 x 38.25 x 20.30 mm


Roller Shutter 2 protects the engine from running for more than 4 minutes. Additionally short break is introduced before changing the direction.

Contact Details

Phone:022 4118500

Request More Information

Details of the product above will be automatically included with your enquiry.